- Model GY Series
- All-in-one Series
- GYSE-P Probe
- GYSE-A Probe
- GYSE-S Probe
- GYSE-Q Probe
- GYLS / GYLT Probe
- GYLS-T / GYLT-T Probe
- GYcAT Probe
- GYAF1 Probe
- Compact Series
- GYMS Probe / GYMSC Controller
- GYGS Probe / GYGSC Controller
- GYPM Probe / GYPMC Controller
- GYPE2K Probe / GYMSC Controller
- GYMT Probe / GYMTC Controller
- High Performance Series
- GYcRS Probe
- GYcRP Probe
- GYMR5 Probe
- GYFRS Probe
- GYHR Probe / GYMNC Controller
- Linear Profile Series
- GYKM Probe / GYMNC Controller
- GYKM-LS / GYKM-LT Probe
- GYKS Probe
- Flexible rod Series
- GYSE-FX-A
- GYSE-FX-S
- GYSE-FX-Q
- Controller
- GYHC Controller
- GYFC2 Controller
- GYDC-05 Controller
- GYCL-201
- Display
- GKS Controller with Display
- DP-50-D
- DP-101-D
- Option
- High Ambient Temperature version
- Waterproof Probe（IP-68）
- SRT option
- Probe with flange or ferrule
- Dead-zone length / Material / Accessories
- Magnet/Float
- Float
- Magnet
- Model GMR Series
- Model CS Series
- Model SMR Series
- Model I-SAC Series
- IMPAK Series
Model GY Series
resolution up to 1μm.
Positon output is Analogue, SSI, or Incremental.
Velocity output (option) is avaiable for Analogue type.
The positonal difference between 2 magnets can be observable
as well.
This allows quick and easy sensor cartrige replacement.
Sensor parameters (zero, full-scale or range) can be adjusted by
using the Windows programming software (ISO9141).
Specifications
| Non-linearity | < ±0.025%FS (Min.±50μm) |
|---|---|
| Resolution | 0.01mm (Standard), 0.1mm, 0.05mm, 0.005mm, 0.002mm, 0.001mm |
| Repeatability | ±0.001%FS (Min.±3μm) |
| Temp drift | ±15ppmFS/°C |
| Output | SSI |
| Position output (Standard) | SSI、24bit Binary (Standard) or Gray code |
| Velocity output (Option) | Non-option |
| Alarm output | Open drain 50V 0.1A (Alarm signal for lost magnet) |
| Power supply | +24 (±2) VDC (80mA) |
| Frequency response | Std 1kHz (depending on stroke) sampling |
| Admissible press. | 35MPa (probe rod) |
| Operating Temp | -20°C-+80°C |
| Storage Temp | -40°C-+80°C |
| Vibration | 15G (10-2000Hz) |
| Shock | 100G (2msec) |
| Protection | IP67 (Connecting mount or Pigtail type) |
The above mentioned accuracy applies to sensors with an effective stroke of 300mm or more.
Model No.
(1):Effective stroke
15mm-5200mm
(2):Thread
M:M24xP1.0 (Standard)
N:M18xP1.5
U:3/4-16UNF-3A
(3):Sensor rod diameter
blank:Φ10 (Standard)
8:Φ8
14Φ13.8
(4)Cable connection
CN:Connector (Standard)
G*:Pigtail type
(*:Cable length [m], Standard:1.5m)
For CN type, only counter connector supplied.
In case extra cable needed, specify the length.
(7):Resolution
D2:0.1mm
D3:0.05mm
D4:0.01mm (Standard)
D5:0.005mm
D7:0.002mm
D8:0.001mm
(8)Direction
D:output data increase toward probe tip
R:output data decrease toward probe tip
(9):Output code
B:binary(Standard)
G:gray
(Note)
VA:when magnet stops, output is 0V. when moving toward probe tip, +10V
WB:when magnet stops, output is 4mA. when moving in any direction, 20mA.
Dimensions
| Probe | Removing sensor element | Connector | Pigtail type (Option) | |||
|---|---|---|---|---|---|---|
 |  |  |  | |||
|
| | |
Material probe head:Al diecast, probe rod:SS304
Standard magnet:No.2Y.
Other magnets are available from Magnet Grouping [GG].
The tip dead zone length (70mm) depends on the magnet or float type.
Connector:LEMO connector (Material:brass with Ni plating)
(Standard:straight type, Option:L type)
