- Model GY Series
- All-in-one Series
- GYSE-P Probe
- GYSE-A Probe
- GYSE-S Probe
- GYSE-Q Probe
- GYLS / GYLT Probe
- GYLS-T / GYLT-T Probe
- GYcAT Probe
- GYAF1 Probe
- Compact Series
- GYMS Probe / GYMSC Controller
- GYGS Probe / GYGSC Controller
- GYPM Probe / GYPMC Controller
- GYPE2K Probe / GYMSC Controller
- GYMT Probe / GYMTC Controller
- High Performance Series
- GYcRS Probe
- GYcRP Probe
- GYMR5 Probe
- GYFRS Probe
- GYHR Probe / GYMNC Controller
- Linear Profile Series
- GYKM Probe / GYMNC Controller
- GYKM-LS / GYKM-LT Probe
- GYKS Probe
- Flexible rod Series
- GYSE-FX-A
- GYSE-FX-S
- GYSE-FX-Q
- Controller
- GYHC Controller
- GYFC2 Controller
- GYDC-05 Controller
- GYCL-201
- Display
- GKS Controller with Display
- DP-50-D
- DP-101-D
- Option
- High Ambient Temperature version
- Waterproof Probe（IP-68）
- SRT option
- Probe with flange or ferrule
- Dead-zone length / Material / Accessories
- Magnet/Float
- Float
- Magnet
- Model GMR Series
- Model CS Series
- Model SMR Series
- Model I-SAC Series
- IMPAK Series
Model GY Series
GYPM Probe / GYPMC Controller
Mini type
The sensor head of GYPM probe is more compact. By new design
of probe head, screw side dead zone has been shortened to 30mm
(Standard). As to tip dead zone, making short to 40mm is possible
by option (standard:70mm). Cable out direction is radial.
GYPM probe is used in combination with the GYPMC controller,
which provides analogue output, 0-10V or 4-20mA, and can also be
used in combination with GYHC or GYDC-05 controller, which
provides velocity output or digital output.
of probe head, screw side dead zone has been shortened to 30mm
(Standard). As to tip dead zone, making short to 40mm is possible
by option (standard:70mm). Cable out direction is radial.
GYPM probe is used in combination with the GYPMC controller,
which provides analogue output, 0-10V or 4-20mA, and can also be
used in combination with GYHC or GYDC-05 controller, which
provides velocity output or digital output.
Specifications
| Non-linearity | < ±0.05%FS TYP |
|---|---|
| Resolution | < 0.01%FS |
| Repeatability | < ±0.01%FS |
| Temp drift | ±70ppmFS/°C (probe) / ±50ppmFS/°C (controller) |
| Voltage output | 0-10V or 10-0V / (output current:Max.5mA, load:Min.2kΩ) |
| Current output | 4-20mA or 20-4mA / (load:Min.500Ω) |
| Power supply | +24 (±2) VDC (100mA) |
| Frequency response | Std 1kHz (depending on stroke) sampling |
| Admissible press. | 35MPa (probe rod) |
| Operating Temp | -5°C-+60°C (probe) / 0°C-+60°C (controller) |
| Storage Temp | -40°C-+80°C |
| Vibration | 6G(or 40Hz 2mmPP) |
| Shock | 20G(2msec) |
| Protection | IP64(probe) |
| Cable length | 1.5m (Standard) (Option Max.100m) |
The above mentioned accuracy applies to sensors with an effective stroke of 300mm or more.
Zero/Gain adjustments by trimmer of controller is possible, std within ±3%FS.
Model No.
(1)Effective stroke
15mm-1000mm
(2)Cable length (m)
Standard1.5m
(1)Output
A:0-10V
B:4-20mA
(2)Direction of output
(toward probe tip)
D:output increase
R:output decrease
(3)Effective stroke
15mm-1000mm
Dimensions
| Probe | Controller | |||||
|---|---|---|---|---|---|---|
 |  | |||||
|
|
Material probe head:SS304、probe head cap:GFRP50 (nylon 66), probe rod:SS304
Standard magnet:No.2PN Other magnets are available from Magnet Grouping [GG].
The tip dead zone length (70mm) depends on the magnet or float type.
After fixing the probe, users can adjust the cable direction (360°) by loosening
the small screw on probe HEX parts and turning the probe head.
