- Model GY Series
- All-in-one Series
- GYSE-P Probe
- GYSE-A Probe
- GYSE-S Probe
- GYSE-Q Probe
- GYLS / GYLT Probe
- GYLS-T / GYLT-T Probe
- GYcAT Probe
- GYAF1 Probe
- Compact Series
- GYMS Probe / GYMSC Controller
- GYGS Probe / GYGSC Controller
- GYPM Probe / GYPMC Controller
- GYPE2K Probe / GYMSC Controller
- GYMT Probe / GYMTC Controller
- High Performance Series
- GYcRS Probe
- GYcRP Probe
- GYMR5 Probe
- GYFRS Probe
- GYHR Probe / GYMNC Controller
- Linear Profile Series
- GYKM Probe / GYMNC Controller
- GYKM-LS / GYKM-LT Probe
- GYKS Probe
- Flexible rod Series
- GYSE-FX-A
- GYSE-FX-S
- GYSE-FX-Q
- Controller
- GYHC Controller
- GYFC2 Controller
- GYDC-05 Controller
- GYCL-201
- Display
- GKS Controller with Display
- DP-50-D
- DP-101-D
- Option
- High Ambient Temperature version
- Waterproof Probe（IP-68）
- SRT option
- Probe with flange or ferrule
- Dead-zone length / Material / Accessories
- Magnet/Float
- Float
- Magnet
- Model GMR Series
- Model CS Series
- Model SMR Series
- Model I-SAC Series
- IMPAK Series
Model GY Series
small head. A fine rod (outside diameter Φ4) and a small head
expand the design flexibility of the equipment. Standard magnet and
float can be used.
With the GYMSC controller, it outputs analogue signal of 0-10V or
4-20mA.
Specifications
| Non-linearity | < ±0.5%FS TYP |
|---|---|
| Resolution | < 0.03%FS |
| Repeatability | < ±0.03%FS |
| Temp drift | < ±0.01%FS/°C (probe) / < ±0.01%FS/°C (controller) |
| Voltage output | 0-10V or 10-0V / (output current:Max.5mA, load:Min.2kΩ) |
| Current output | 4-20mA or 20-4mA / (load:Min.500Ω) |
| Power supply | +24 (±2) VDC (100mA) |
| Frequency response | approx 1kHz sampling (Note1) |
| Admissible press. | 18MPa (probe rod) |
| Operating Temp | -20°C-+80°C (probe) / 0°C-+60°C (controller) |
| Storage Temp | -40°C-+80°C |
| Vibration | 3G (or 40Hz 1mmPP) |
| Shock | 20G (2msec) |
| Protection | IP64 (probe) |
| Cable length | 1.5m (Standard) (Option Max.5m) |
The above mentioned accuracy applies to sensors with an effective stroke of 100mm or more.
Zero/Gain adjustments by trimmer of controller is possible, std within ±3%FS.
(Note1)liquid level application:approx 100Hz sampling
Model No.
(1):Effective stroke
50mm-250mm
(2):Cable length (m)
Standard 1.5m
Thread:M18x1.0, Rod:Φ4
(Note2)
Please use the cable as specified though it is possible to extend
to Max.5m in case so specified in advance. (The cable cannot be
extended, nor cut.) The terminal stand or connector etc. can be
used to arrange cable length.
(1):Output
A:0-10V
B:4-20mA
(2):Effective stroke
50mm-250mm
(3):Direction of output
(toward probe tip)
D:output increase
R:output decrease
Dimensions
| Probe | Controller | Ti float | ||||
|---|---|---|---|---|---|---|
 |  |  | ||||
|
| |
Material probe head:SS316、probe rod:SS316
Standard magnet:No.Φ、float:Ti-float
The M5 screw installed in the rod tip can be used as float stopper or to fix the sensor.
When the sensor rod part is to be sealed, O ring should be used, refer to detail A drawing.
