- Model GY Series
- All-in-one Series
- GYSE-P Probe
- GYSE-A Probe
- GYSE-S Probe
- GYSE-Q Probe
- GYLS / GYLT Probe
- GYLS-T / GYLT-T Probe
- GYcAT Probe
- GYAF1 Probe
- Compact Series
- GYMS Probe / GYMSC Controller
- GYGS Probe / GYGSC Controller
- GYPM Probe / GYPMC Controller
- GYPE2K Probe / GYMSC Controller
- GYMT Probe / GYMTC Controller
- High Performance Series
- GYcRS Probe
- GYcRP Probe
- GYMR5 Probe
- GYFRS Probe
- GYHR Probe / GYMNC Controller
- Linear Profile Series
- GYKM Probe / GYMNC Controller
- GYKM-LS / GYKM-LT Probe
- GYKS Probe
- Flexible rod Series
- GYSE-FX-A
- GYSE-FX-S
- GYSE-FX-Q
- Controller
- GYHC Controller
- GYFC2 Controller
- GYDC-05 Controller
- GYCL-201
- Display
- GKS Controller with Display
- DP-50-D
- DP-101-D
- Option
- High Ambient Temperature version
- Waterproof Probe（IP-68）
- SRT option
- Probe with flange or ferrule
- Dead-zone length / Material / Accessories
- Magnet/Float
- Float
- Magnet
- Model GMR Series
- Model CS Series
- Model SMR Series
- Model I-SAC Series
- IMPAK Series
Model GY Series
processing electronics of GYcAT series is integrated into a
transducer head.
You can get a voltage or current analog signal proportional to a
magnet position only by applying a 24V dc power supply directly to
the transducer.
GYcAT series have alarm output and head is equipped with noise
cancellation functions.
Specifications
| Non-linearity | < ±0.05%FS TYP |
|---|---|
| Resolution | < 0.01%FS |
| Repeatability | < ±0.01%FS |
| Temp drift | 40ppm FS/°C |
| Voltage output | 0-10V or 10-0V / (output current:Max.5mA, load:Min.2kΩ) |
| Current output | 4-20m or 20-4mA / (load:Min.500Ω) |
| Alarm output | Open collector 30V 0.1A |
| Power supply | +24 (±2) VDC (100mA) |
| Frequency response | Std 1kHz (depending on stroke) sampling |
| Admissible press. | 35MPa (probe rod) |
| Operating Temp | -20°C-+65°C |
| Storage Temp | -40°C-+80°C |
| Vibration | 6G (or 40Hz 2mmPP) |
| Shock | 50G (2msec) |
| Protection | IP65 |
The above mentioned accuracy applies to sensors with an effective stroke of 300mm or more.
Model No.
(1):Effective Stroke
15mm-2500mm
(2):Output
A:0-10V
B:4-20mA
C:others (bipolar etc)
(3):Direction of output
(toward probe tip)
D:output data increase
R:output data decrease
(4):Thread
M:M24xP1.0 (Standard)
N:M18xP1.5
U:3/4-16UNF
(5):Sensor rod diameter
blank:Φ10 (Standard)
8:Φ8
14:Φ13.8
(6):Cable connection
CN:Connector (Standard)
G*:Pigtail type
(*:Cable length [m], Standard:1.5m)
Connector:straight type
Connector:only counter connector is supplied. In case cable needed,specify cable length.
Dimensions
| Connector type (Standard) | Pigtail type (Option) | |||||
|---|---|---|---|---|---|---|
 |  | |||||
|
|
Material probe head:Al diecast, probe rod:SS304
Standard magnet:No.2P. Other magnets are available from Magnet Grouping [B].
The tip dead zone length (70mm) depends on the magnet or float type.
The length of the cable should be less than 10m in case of using the voltage output type
and 100m in case of using the current output type.
Connector:Sanwa SNW-1607-PCF (Material:zinc alloy fluoroplastic)
Applied cable diameter:Φ6.6-Φ7.5
Wire size:Less than 0.5mm2
Connection
1 DC24V
2 NC
3 0V
4 SIG COM
5 Voltage output
6 (Current output)
7 Alarm output
*Shield should be connected with 0V at user side.
